[ 1.10.44 ] - modified the recovery routine for printing on the monocrome ribbon (K ribbon). - modified the function for setting the card ejecting angle (-180~+180) of the printer's back side after installing the flipper. - the Auto Card-In operation can be performed when the error of the Card-In flag is cleared. - modified the operating period of the DC motor from 300ms to 700ms when the Card-Out is performed under the MagneticSimpleWRMode. - the non-printinf fixel is added to the start of the printing data. - when the Card-Back-Out option is set, the Back-Out function is performed regardless of the flipper status. - the Card-Back-Out command can be operated regardless of the status of the Error-Back-Out option when the laminator is installed. - Uart1 bypass can be operated regardless of the SBS. [ 1.10.37 ] - fixed the problem that issue a blank card when cancel the print after error occurred in batch printing by using K ribbon. - added the function for automatic printer cleaning by pushing two LED buttons on the front side of printer for 5 seconds at the same time (before pushing two LED buttons, open the top cover and remove the ribbon). - modified the counter algorithm for the K ribbon (after receiving the printing data and printing a card, decrease the ribbon counter. - modified the card out function (if there is no card, the flipper motor don't work when the printer eject a card, even if the flipper is installed). [ 1.10.32 ] - added the function for auto restoration of the printing panel when problem occur in the middle of prining some panel. - deleted Board Type 1 and 2. If the Board Type is set to 1 or 2, the Board Type will be set to 3 automatically. - added the function for User Memory Block, Total 8 blocks and each block is 4 bytes (add SBS command). - added user display command for graphic LCD(ST920) (add SBS command). - added the function for multilingual messages on graphic LCD(ST920) (Arabic, English) - added the ribbon type for hYMCKOKO that can print 250 cards. - added the function for taking a card from hopper to ptiner automatically when the card sensed by the hopper sensor or the rotator card out sensor (for KIOSK) [ 1.10.27 ] - support Graphic LCD (ST7920 GLCD) - enable to turn Soft Power off under PrintLockCheck(PHYSICAL_KEY,PC_NAME,ROOT_PASSWARD,USER_PASSWARD) - added HYMCKOKO ribbon - modified MAGENTA color level of standard ribbon (BLUE LED : 2800 -> 2400) for supporting HYMCKOKO ribbon - modified function for displaying "Ribbon Count = 0" on LCD when balance of Monochrome ribbon is "0" - added new auto mode of magnaetiv stripe encodeing for HiCo or LoCo card - added simple write mode for fast magnetic stripe encoding under using B ribbon. - added ballys write mode of magnetic stripe encoding - add UART Bypass Mode - added RFWaitingMode for waiting contactless samrtcard on contactless encoding position - added RFWaitingTime (milliseconds) for adjusting waiting time of RFWaitingMode [ 1.10.16 ] - added the recovery function when error occurs while line printing [ 1.10.14 ] - added the function of magnetic bit mode in spooler printing - changed the encoding density to track1&track3 = 210dpi,track2 = 75dpi in magnetic bit - added the fuction to use 1/3YMCKOK & hYMCKO - changed the max panel size of 1/3 and half panels.(1/3 max.25mm, half max.40mm) - added the routine to fix the error of counting ribbon after printing [ 1.10.10 ] - changed the card position of contact/contactless smart card encoding for SMART-30. - changed the operation to stop printing when the time of print head's operation is abnormal - changed the LCD message to show "Film Zero" and "Film Empty" by priority when these errors occurs - changed the LCD message to add "+" mark after error code when multi errors occurs - fixed the bug that can't set "error card back out" when the flipper is installed (starting after 1.00.88) - fixed the bug that printer stops because card-in command doesn't operate when laminator has communication problem with PC in SBS mode - fixed the bug of finding standard Magenta panel [ 1.10.03] - added the "Sort Quiet" option to minimize the noise in SMART-30 model - changed the algorithm of moving a card because of noise - changed the algorithm of moving a card in the magnetic stripe part to adjust magnetic encoding position - fixed the bug of printing 3rd page automatically when it cancel to print by clicking left LED button while occurring error [ 1.00.88 ] - added the function of "BackOut" when the Laminator is installed - added the "High" speed in advanced options to enhance the print speed (2.5 sec / panel) - changed the ribbon motor's torque to 1500 when Premium ribbon is installed - changed the algorithm of color search when Standard ribbon is installed (changed the level of black panel) [ 1.00.78 ] - fixed the bug of occurring time out error in pipeline mode on short printing time - changed the initialization process that operating head up/down after initializing laminator [ 1.00.74 ] - changed the LCD format to display the error message of laminator - changed the location of the card in printer after doing laminate command in SBS mode - fixed the bug of recognizing of the printer and re-printing issue after printing once in Apple Mac [ 1.00.68 ] - added the control command of Laminator - added the function to move to rotator in Laminator - added the functions to interwork with Laminator f/w ver. 1.00.04 [ 1.00.66 ] - added the 24LC08 code - fixed the setting to prohibited downgrading under f/w ver. 1.00.66 in using 24LC08 memory - improved performance of the Laminator driving part