[ 1.10.54 ] - added the function for changing the card feeding direction on SMART-30 when the top is opened and press the button on the front side of SMART-30 twice continuously. - added the slow printing mode of K ribbon (5.2 seconds per card) in CardPrinterSetup utility. [ 1.10.52 ] - modified the card out back function. When the laminator module is installed, if the laminator stacker cover is not opened, cards can be ejected to the front stacker even if the Card Out option is set to the Back. - added the function for displaying the text error message. - added the Permanent mode on the Cleaning Warning option, the Permanent mode is to display the cleaning warning message until clean the printer. - added the function for displaying the IP and MAC address on the LCD of SMART-50. by using the left LED button on the control panel of the printer. - modified the error procedure of the card out error on conditon that the laminator module is installed. When a card is jammed in the printer module after the laminator, the card out error occurs. [ 1.10.47 ] - modified the downloading block size (1KB to 2KB) when the laminator firmware is being downloaded for updating. - fixed the bug which the recovery process isn't performed when the laminator firmware is being downloaded and some error occurs. - modified the command for the card-in position of the flipper. [ 1.10.44 ] - modified the recovery routine for printing on the monocrome ribbon (K ribbon). - modified the function for setting the card ejecting angle (-180~+180) of the printer's back side after installing the flipper. - the Auto Card-In operation can be performed when the error of the Card-In flag is cleared. - modified the operating period of the DC motor from 300ms to 700ms when the Card-Out is performed under the MagneticSimpleWRMode. - the non-printinf fixel is added to the start of the printing data. - when the Card-Back-Out option is set, the Back-Out function is performed regardless of the flipper status. - the Card-Back-Out command can be operated regardless of the status of the Error-Back-Out option when the laminator is installed. - Uart1 bypass can be operated regardless of the SBS. [ 1.10.37 ] - fixed the problem that issue a blank card when cancel the print after error occurred in batch printing by using K ribbon. - added the function for automatic printer cleaning by pushing two LED buttons on the front side of printer for 5 seconds at the same time (before pushing two LED buttons, open the top cover and remove the ribbon). - modified the counter algorithm for the K ribbon (after receiving the printing data and printing a card, decrease the ribbon counter. - modified the card out function (if there is no card, the flipper motor don't work when the printer eject a card, even if the flipper is installed). [ 1.10.32 ] - added the function for auto restoration of the printing panel when problem occur in the middle of prining some panel. - deleted Board Type 1 and 2. If the Board Type is set to 1 or 2, the Board Type will be set to 3 automatically. - added the function for User Memory Block, Total 8 blocks and each block is 4 bytes (add SBS command). - added user display command for graphic LCD(ST920) (add SBS command). - added the function for multilingual messages on graphic LCD(ST920) (Arabic, English) - added the ribbon type for hYMCKOKO that can print 250 cards. - added the function for taking a card from hopper to ptiner automatically when the card sensed by the hopper sensor or the rotator card out sensor (for KIOSK) [ 1.10.27 ] - support Graphic LCD (ST7920 GLCD) - enable to turn Soft Power off under PrintLockCheck(PHYSICAL_KEY,PC_NAME,ROOT_PASSWARD,USER_PASSWARD) - added HYMCKOKO ribbon - modified MAGENTA color level of standard ribbon (BLUE LED : 2800 -> 2400) for supporting HYMCKOKO ribbon - modified function for displaying "Ribbon Count = 0" on LCD when balance of Monochrome ribbon is "0" - added new auto mode of magnaetiv stripe encodeing for HiCo or LoCo card - added simple write mode for fast magnetic stripe encoding under using B ribbon. - added ballys write mode of magnetic stripe encoding - add UART Bypass Mode - added RFWaitingMode for waiting contactless samrtcard on contactless encoding position - added RFWaitingTime (milliseconds) for adjusting waiting time of RFWaitingMode [ 1.10.16 ] - added the recovery function when error occurs while line printing [ 1.10.14 ] - added the function of magnetic bit mode in spooler printing - changed the encoding density to track1&track3 = 210dpi,track2 = 75dpi in magnetic bit - added the fuction to use 1/3YMCKOK & hYMCKO - changed the max panel size of 1/3 and half panels.(1/3 max.25mm, half max.40mm) - added the routine to fix the error of counting ribbon after printing [ 1.10.10 ] - changed the card position of contact/contactless smart card encoding for SMART-30. - changed the operation to stop printing when the time of print head's operation is abnormal - changed the LCD message to show "Film Zero" and "Film Empty" by priority when these errors occurs - changed the LCD message to add "+" mark after error code when multi errors occurs - fixed the bug that can't set "error card back out" when the flipper is installed (starting after 1.00.88) - fixed the bug that printer stops because card-in command doesn't operate when laminator has communication problem with PC in SBS mode - fixed the bug of finding standard Magenta panel [ 1.10.03] - added the "Sort Quiet" option to minimize the noise in SMART-30 model - changed the algorithm of moving a card because of noise - changed the algorithm of moving a card in the magnetic stripe part to adjust magnetic encoding position - fixed the bug of printing 3rd page automatically when it cancel to print by clicking left LED button while occurring error [ 1.00.88 ] - added the function of "BackOut" when the Laminator is installed - added the "High" speed in advanced options to enhance the print speed (2.5 sec / panel) - changed the ribbon motor's torque to 1500 when Premium ribbon is installed - changed the algorithm of color search when Standard ribbon is installed (changed the level of black panel) [ 1.00.78 ] - fixed the bug of occurring time out error in pipeline mode on short printing time - changed the initialization process that operating head up/down after initializing laminator [ 1.00.74 ] - changed the LCD format to display the error message of laminator - changed the location of the card in printer after doing laminate command in SBS mode - fixed the bug of recognizing of the printer and re-printing issue after printing once in Apple Mac [ 1.00.68 ] - added the control command of Laminator - added the function to move to rotator in Laminator - added the functions to interwork with Laminator f/w ver. 1.00.04 [ 1.00.66 ] - added the 24LC08 code - fixed the setting to prohibited downgrading under f/w ver. 1.00.66 in using 24LC08 memory - improved performance of the Laminator driving part